View LA2360M_4801811.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Ordering number : ENA0191
LA2360M
Overview
Monolithic Linear IC
CAN Transceiver
The LA2360M is a CAN (Controller Area Network) transceiver.
Functions
[ Transmitter block ] * Low-pass filter (EMI prevention) * Output driver [ Receiver block ] * ATT * Comparator
Features
* Conforms to the ISO 11898 standard * Transmission rate: 1 Mbps
Specifications
Maximum Ratings at Ta = 25C
Parameter Maximum supply voltage Maximum applied voltage Maximum applied voltage (pins 6 and 7) Allowable power dissipation Operating temperature Storage temperature Pd max Topg Tstg
3
Symbol VCC max Vap Vap (6, 7)
Conditions
Ratings 6.0 VCC -8 to +18
Unit V V V mW C C
*: Mounted on a circuit board, Ta 85C
440 -40 to +85 -55 to +150
*: Circuit board: 39.8x50.0x1.6mm glass epoxy Notice: Please contact our company, when using the LA2360M in the body system or the power-train system.
Any and all SANYO Semiconductor products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO Semiconductor representative nearest you before using any SANYO Semiconductor products described or contained herein in such applications. SANYO Semiconductor assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor products described or contained herein.
92706 / 10606 MS OT 20051110-S00002 No.A0191-1/5
LA2360M
Operating Conditions at Ta = 25C
Parameter Recommended supply voltage Operating supply voltage range Symbol VCC VCC op Conditions Ratings 5.0 4.5 to 5.5 Unit V V
Operating Characteristics at Ta = 25C, VCC = 5.0V
Parameter Overall Current drain ICC Dominant; V1 = 1V, R8 = 0 Recessive; V1 = 4V, R8 = 47k Recessive; V1 = 4V, R8 = 0k Standby; V8 = VCC, I1 = I4 = I5 = 0mA DC transmitter block High-level input voltage Low-level input voltage High-level input current Low-level input current CAN_H output voltage CAN_L output voltage Recessive state bus voltage Pins 6 and 7 output voltage difference Current when pin 7 grounded Current when pin 6 shorted to VCC DC receiver block Differential input voltage (recessive) Differential input voltage (dominant) High-level output voltage (pin 4) Low-level output voltage (pin 4) Input hysteresis voltage DC standby/slope control block High-speed mode input voltage High-speed mode input current Standby mode input voltage Slope control mode current Slope control mode voltage V8 I8 Vstb Islope Vslope 8pin = 47k 8pin = 47k V8 = 0V 0.75VCC -200 0.4VCC -10 0.6VCC 0.3VCC -500 V A V A V V4OH V4OL Vdiff (hys) Vdiff (d) Vdiff (r) Output -recessive Output -recessive, 0V < (V6, V7) < 12V Output -dominant Output -dominant, 0V < (V6, V7) < 12V I4 = -100A I4 = +100A -1.0 -1.0 0.9 1.0 0.8VCC 0 50 80 0.2 0.1 5.0 5.0 VCC 0.2VCC 150 V V V V V V mV ISC7 ISC6 V1IH V1IL I1IH I1IL V7 V6 V6, 7 V6, 7 Output -recessive Output -dominant V1 = 4V V1 = 1V V1 = 1V V1 = 1V V1 = 4V V1 = 1V V1 = 4V; With no 62 resistor V1 = 1V, V7 = -8V; VCC = 5V V1 = 1V, V6 = 18V 0.7VCC -0.3 -200 -600 2.75 0.5 2.0 1.5 -500 VCC+0.3 0.3VCC +30 -100 4.5 2.25 3.0 3.0 +50 -120 160 V V A A V V V V mV mA mA 30 50 30 70 14 18 70 mA mA mA A Symbol Conditions min Ratings typ max Unit
Continued on next page.
No.A0191-2/5
LA2360M
Continued from preceding page. Parameter DC reference block Output reference voltage Vref V8 = 1V; -50A < I5 < 50A V8 = 4V; -5A < I5 < 5A AC transmitter block Pins 6 and 7 differential output pulse width Rise delay time tonTXD twidth (diff) V8 = 1V, V1 = 1MHz V8 = 1V, V1 = 100kHz V8 = 1V, V1 = 1MHz V8 = 1V, V1 = 100kHz Fall delay time toffTXD V8 = 1V, V1 = 1MHz V8 = 1V, V1 = 100kHz AC receiver block (overall) (See note 1.) Rise delay time tonRXD V8 = 1V, V1 = 1MHz V8 = 1V, V1 = 100kHz R8 = 47k, V1 = 100kHz R8 = 24k, V1 = 100kHz Fall delay time toffRXD V8 = 1V, V1 = 1MHz V8 = 1V, V1 = 100kHz R8 = 47k, V1 = 100kHz R8 = 24k, V1 = 100kHz Pin 8 wakeup time from standby mode Receiver output response time to a bus level change tdRXDL V1 = 4.0V, V8 = 4.0V [BUS] recessive dominant 3 s twake V8 = 4V 1V, V8 = 100kHz 110 110 360 320 90 90 600 500 160 160 500 500 160 160 800 800 20 ns ns ns ns ns ns ns ns s 0.45 4.5 40 40 40 40 0.55 5.5 65 65 65 65 s s ns ns ns ns 0.45VCC 0.4VCC 0.55VCC 0.6VCC V V Symbol Conditions min Ratings typ max Unit
Note 1. With an input signal to the transmitter, in automatic send/receive mode
Package Dimension
unit:mm 3032D
5.0 8 5
4.4 6.4
1 (0.65) 1.27
4 0.35
1.7max (1.5)
0.15
SANYO : MFP8(225mil)
0.1
0.63
No.A0191-3/5
LA2360M
Block Diagram
Pin Functions
Pin No. 1 2 3 4 5 6 7 8 Pin TXD GND VCC RXD VREF CANL CANH RS I/O I P P O O I/O I/O I Function Transmission signal input GND Power supply Reception signal output Reference voltage output Transmission signal output (L) Transmission signal output (H) Mode switching resistor Description Input from the CAN microcontroller System ground 5V Output to the CAN microcontroller 2.5V Input and output of send and receive signals to the bus Input and output of send and receive signals to the bus Slope control Controls standby mode
No.A0191-4/5
LA2360M
Specifications of any and all SANYO Semiconductor products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Semiconductor Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor products (including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Semiconductor Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO Semiconductor believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of January, 2006. Specifications and information herein are subject to change without notice. PS No.A0191-5/5

▲Up To Search▲

Price & Availability of LA2360M

	To Download LA2360M Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .